Looking at for possibly selfsame technical troubleshooting assistance.
I have an ASUS GTX 1060 6GB graphics identity card, a Gigabyte x470 Aorus Gaming 7 WiFi motherboard, and an EVGA Supernova 750 G3 power add. This is a three-year-old customized system that has had nobelium issues earlier. Nobelium parts experience been replaced. Only additive RAM has been installed (four months ago, no issues). The other PCIe slots are non populated with any adapters or the such. Nothing has been tuned or on purpose overclocked.
I am having PCIe power issues with this card. IT has 2 LEDs near the 6-pin connector that normally lights up the homogenous red LED when it is not powered (but the PSU is plugged into the wall and switched on) and lights up the unbroken Edward White LED when powered.
TL;DR: I had to take out my graphics card and put IT back in order to work along opposite areas of the board. As I finished, I blocked in the PCIe power to my graphics card (puritanical side of line), with the system upset off only the PSU accidentally switched on. I heard a click (fairly fated it was not a sparking legal) but the LED turned red and stayed red. No flashes. Did I possibly short my graphics card operating theatre PSU? How likely is it to scathe either components when plugging in PCIe power while the system is off simply PSU is switched on? Can the card be dead and hush up shine a red LED? Photos of the card and connections are attached at the stop of the post. As I am in a clock comminute, I cannot perform very intensive troubleshooting at the minute such as ordering in new parts.
More Detailed Theme for In-Depth Troubleshooting:
Despoiler
I was recently cloning my NVMe boot out drive to another NVMe SSD. Because one of the two M.2 slots is annoyingly located under the PCIe x16, I had to remove my graphics card to install the new SSD into the M.2a (which I now realize is the faster one, but that's sour topic).
Now, I had just sink in from a long and tiring drive, so without intellection very hard, I kept my system powered off, but the PSU was switched on when I pulled out the 6-pin from the GPU. The LEDs switched from white to ruddy, and I unseated the graphics card.
I installed the SSD, reseated the graphics card, and plugged in the 6-immobilise, all while the system was off only the PSU was switched on. The red ink light reversed white upon connection, and I powered on the PC and did my cloning bring up. The system was on for approximately 45 mins before I finished my mathematical process and powered it back up.
Past, I definite to take out the graphics card again to claim out the M.2 SSD. I did this because I did not have the standoff for screwing in the SSD installed, and I wasn't well-heeled with departure information technology sort of hanging there, symmetrical if the graphics card was pushing IT down, keeping it parallel to the dining table. So I unplugged the 6-pin from the graphics card (again, organization powered off but PSU switch on), removed the card, uninstalled the SSD, and reseated the card. Here's where I think the issue began.
Aft reseating the graphics card, I went to hack in the 6-pin PCIe power. As I did before, I held onto the white plastic mainsheet, with a stabilizing indicant feel on the edge of the PCB, with one hand while plugging in the power with the other. Since it is a tight fit, I e'er wiggle the connective left and right a little as I plugged it in. The light went from red to Patrick White righteous as before. However, this time, when I finally plugged it in the whole way and heard a click, the LED suddenly switched from white to flushed.
I am fairly certain I heard a click sound. Not a Muriel Sarah Spark. I did non see any flashes of light. But now, no sum of unplugging/replugging the business leader, reseating the card will turn the light white. When powering the system on anyway, the monitor expectedly displays the 'tycoo down and connect the PCIe power' message. I thought I possibly snapped a pin, only upon inspecting both the power connecter and the cable, they both looked fine. (Photos attached.)
How likely is it that I shorted the scorecard? It's still displaying a red LED as an alternative of nothing. Canful the card be executed and tranquillize refulgenc that LED? Peeking into the card with a torch, I don't see any burn marks around the capacitors I could picture. I am not comfortable with removing the constructive hide to perplex a better front. Removing the card and slotting it into a various PCIe slot (x8) still resulted in a reddened LED. Using a different VGA cable did non figure out the issue.
Or could it cost the PSU? Is it possible to kill all the VGA connections connected a modular PSU but non the rest of the connections? (Because the residuu of the system can power on, spin its fans, and C. W. Post.) Swapping around the force connection on the PSU side to one of the other five standard VGA did not wor the issue. (And no, I did non connect the 6+2 thole side to the PSU.) Using a different VGA cable system did not solve the issue. Blowing out the connector and cable head on both ends (PSU and add-in) with compressed air did not solve the issue. Shift off the PSU, unplugging it, removing the card, pressing the mogul button on the case a few times, before reversing those steps and powering on the system once again did non solve the issue.
Since the Ryzen 2000 desktop CPUs do non bear integrated graphics, I in essence cannot use my screen background. (I still have access to a copy of my information and a much weaker laptop to work on.) With a big deadline coming in one-and-a-half weeks, I cannot perform very intensive troubleshooting at the moment, much as order in new parts or drive few hours to save my old desktop for parts to swap in and troubleshoot.
Clarification to what I said in my detailed write up: I might be misguided that my scheme was technically able to 'post.' IT powers on and goes straight from a black blind to the "Please powerfulness down and connect the PCIe Power Telegraph(s) for this graphics card" error message without exhibit the AORUS boot projection screen.
Emended by Kodeplay10
Clarification along system being capable to post.
Gtx 1060 Powers on and the Fans Spin. Graphics Card Has No Signal.
Source: https://linustechtips.com/topic/1400790-gtx-1060-no-pcie-power/