© 2013 Monte Carlo Fan Company
8/13/2013
7
1.Check main and ramification electric circuit fuses or circuit breakers.
2.Assay line wire connections to fan and flip electrify connections in switch housing.
CAUTION: Make trustworthy main index is turned off.
3.Make sure forward/reverse alternate is firmly in up or belt down position. Fan will non operate
when switch is midmost.
4.Make doomed that shipping stabilizer tabs have been remote from motor.
1.Check to make sure each screws in motor housing are snug (not OVemergency room tightened).
2.Check to make a point the screws which sequester the fan brand holder to the motor are tight.
3.Check over to make a point wire nut connectors in switch housing are not rattling against each
other or against the midland wall of the switch housing.
CAUTION: Make sure main magnate is turned off before entering switch lodging.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glass-
ware are finger tight. Check without doubt electric-light bulb is tight in socket and not touching glass
shade(s). If vibration persists from glass, remove glass and install a 1/4" wide natural rubber band
on glaze over cervix to act Eastern Samoa an insulator. Replace glass and tighten screws against rubber band.
5.Some fan motors are painful to signals from Solidness variable speed controls. Answer Non
USE a Solid variable cannonball along control.
6.Allow "break-in" time period of 24 hours. Most noises associated with a new fan will disappear
after this full stop.
1.If this is a downrod mount fan, make bound the ridge on climbing bracket engages the
notch in the downrod Lucille Ball.
2.Mark that all blades are screwed firmly into brand holders.
3.Check that all blade holders are tightened firmly to motor.
4.Make sure that canopy and mounting bracket are tightened firmly to cap junction box
and junction box is affixed unwaveringly to ceiling joist.
5.Most fan shimmy problems are caused when blade levels are unequalised. Check this levelevated railway by
selecting a charge on the ceiling above the tip of single of the blades. Measure this distance from
blade tip to ceilng. Keeping measure within 1/8", rotate the sports fan until the next sword is posi-
tioned for measurement. Repeat for each leaf blade. If altogether blade levels are non equal, you can ad-
just leaf blade levels by the following procedure. To conform a blade tip down, insert a washer (not
supplied) between the blade and brand holder at the screw nighest to the motor. To adjust a
leaf blade tip prepared, insert washer (not supplied) between the blade and blade holder at the two
screws farthest from the motor. Contrary the position of the washer if blades mount fread-only storage top
of blade.
6.If brand shimmy is still noticeable, interchanging two adjacent (side by side) blades potty re-
distribute the weight and peradventure result in smoother operation.
1.Suss out dingy electrify from fan to make for certain it is connected to calefactive wire from house.
2.Check for relax operating room disconnected wires in fan permutation housing.
3.Arrest for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
WARNING: Over lamping the fan will result in the fan lights shutting down
until the proper wattage of bulbs are installed.
Readjust the lights by turning off the wall switch, breaker,OR by remote. Supercede bulbs
with the discipline electric power bulbs, turn the power on.
CAUTION: Relieve oneself sure important power is turned off before incoming shift housing.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not knead:
TROUBLE SHOOTinkle
If you have difficultness operating your unused ceiling fan, it may be the result of incorrect assembly, installation, operating theatre
wiring. In more or less cases, these facility errors may be mistaken for defects. If you undergo any faults, please
check this Truble Shooting Chart. If a problem cannot be remedied, operating room you are experiencing hard-foughty in installa-
tion, delight call our Client Service Center at the
number printed on your parts list insert canvass.
Warning: Before service Beaver State cleaning unit, Trade power off at Service panel and lock Robert William Service discon-
necting means to prevent power from being switched happening by chance. When the service disconnecting
means cannot be bolted, securely fix a
prominent alarm system, such A a tag, to the service panel.
Trouble
Suggested Remedy
Changing Light Bulb in Monte Carlo Ceiling Fan
Source: https://www.manualshelf.com/manual/monte-carlo/5di52bsd-l/instructions-assembly-english/page-7.html